Leds + Flashing Brake Light = Double Safety

Universal Compact Two Function Strobe Module

Improved Design

Only 1-3/4" x 1-3/8" x 1"

New design has no battery to burn out

Uses: 

7507, 1156,3156, 7440, 921 single circuit bulbs & 7225, 1157, 3157, 7443 dual circuit bulbs, or use with any led light bulb or led fixture.  **Can be used in any 6 or 12 volt (-) ground or (+) ground systems.

Common Applications:

Brake light Warning Strobe
Reverse Light Warning Strobe

Make any led bulbs or lights strobe continuously.

Function:

The FM-02 module contains a chip that will cause an led light bulbs to operate as follows (Note: Use either the White wire or Blue wire not both):

Function 1 (If you use the White Wire)

1.  Each time power is applied to the red wire, from the battery, the white wire to the led bulb will cause the led bulb to perform a sequence as follows;

A.  The led will strobe brightly for a few seconds and then stop strobing.

B.  After a few seconds of strobing, the led light will light bright in a constant-on mode for as long as power is continually applied to the circuit (ie: as long as the brake pedal is pressed).

*C.  When power is cut to the brown wire (ie: the brake pedal is released, the bulb will go dim.  

*Note 1: In a singe circuit bulb such as an 1156 or 921, there is no dim circuit, so the module will sequence whenever the brake is applied, but there will be no dim function.

Uses: 

7507, 1156,3156, 7440, 921 single circuit bulbs & 7225, 1157, 3157, 7443 dual circuit bulbs, or use with any led light bulb or led fixture.  **Can be used in any 6 or 12 volt (-) ground or (+) ground systems

Common Applications:

Brake light Warning Strobe
Reverse Light Warning Strobe

The FM-03 module contains a chip that will cause an led light bulbs to operate as follows:

1.  Each time power is applied to the white wire, from the brake circuit,  the led bulb will perform a sequence as follows;

A.  The led will strobe brightly for a few seconds and then stop strobing.

B.  As long as power is still applied from the white-blue brake wire, the led light will light bright for as long as power is continually applied to the circuit (ie: as long as the brake pedal is pressed).

* B.  When power is cut to the white wire (ie: the brake pedal is released, the bulb will flash again for 2 seconds and then  go dim.

* Note: In a singe circuit bulb such as an 1156 or 921, there is no dim circuit, so the module will sequence whenever the brake is applied, but there will be no dim function.

**Note 2: This module can also be used in a positive ground 6 or 12 volt electrical system.

Uses: 

7507, 1156,3156, 7440, 921 single circuit bulbs & 7225, 1157, 3157, 7443 dual circuit bulbs, or use with any led light bulb or led fixture.  **Can be used in any 6 or 12 volt (-) ground or (+) ground systems,

Common Applications:

Brake light Warning Strobe
Reverse Light Warning Strobe

Make any Led bulbs or lights strobe continuously.

The FM-01 module contains a chip that will cause an led light bulbs to operate as follows (Note: Use either the White wire or Blue wire not both):

Function 1 (If you use the White Wire)

1.  Each time power is applied to the red wire, from the battery, the white wire to the led bulb will cause the led bulb to perform a sequence as follows;

A.  The led will strobe brightly for a few seconds and then stop strobing.

B.  After a few seconds of strobing, the led light will light bright in a constant-on mode for as long as power is continually applied to the circuit (ie: as long as the brake pedal is pressed).

*C.  When power is cut to the brown wire (ie: the brake pedal is released, the bulb will either go dim.

*Note 1: In a singe circuit bulb such as an 1156 or 921, there is no dim circuit, so the module will sequence whenever the brake is applied, but there will be no dim function.

Uses: 

7507, 1156,3156, 7440, 921 single circuit bulbs & 7225, 1157, 3157, 7443 dual circuit bulbs, or use with any led light bulb or led fixture.  **Can be used in any 12 volt (-) ground or (+) ground systems. Will not work in 6 volt systems.

Common Applications:

Brake light Warning Strobe
Reverse Light Warning Strobe

Function:

The FM-00 module contains a chip that will cause an led light bulb or any 12 volt led light to operate as follows:

1.  Each time power is applied to the brown wire, from the battery, the black wire to the led bulb will cause the led bulb to perform a sequence as follows;

A.  The led will strobe brightly for a few seconds and then stop strobing***.

B.  After a few seconds of strobing, the led light will light bright in a constant-on mode for as long as power is continually applied to the circuit (ie: as long as the brake pedal is pressed).

*C.  When power is cut to the brown wire (ie: the brake pedal is released, the bulb will go dim.

*Note 1: In a singe circuit bulb such as an 1156 or 921, there is no dim circuit, so the module will sequence whenever the brake is applied, but there will be no dim function.

Installation:

Install the module anywhere between the battery power and the led light that you wish to make flash.  Connect the wires as follows:

Connect the flashing module in the wires feeding to any led bulb as follows:

White Wire - Connect to the (+) side of any led light(s) that you want to strobe intermittently for the first 20 ms).

Red Wire - Connect to (+) Wire on the Power or Battery Side.

Black Wires - Splices into to the - ground wires on both sides.

Blue Wire - Connect to the (+) side of any led light(s) that you want to strobe continuously.

Installation:

Install the module anywhere between the battery power and the led light that you wish to make flash.  Connect the wires as follows:

Connect the flashing module in the wires feeding to any led bulb as follows:

* Blue Input Wire - Connect to the (+) battery power to power the module.

White Input Wire - Connect to (+) Brake Circuit.

Black Input Wire - Connect to the - ground wire.

Red Output Wire - Connect to the (+) side of any led light(s) or Bulb(s).

Black Output Wire - Connect to to the - ground wire going to the led light.

Installation:

Install the module anywhere between the battery power and the led light that you wish to make flash.  Connect the wires as follows:

Connect the flashing module in the wires feeding to any led bulb as follows:

White Wire - Connect to the (+) side of any led light(s) that you want to strobe intermittently for the first 20 ms).

Red Wire - Connect to (+) Wire on the Power or Battery Side.

Black Wires - Splices into to the - ground wires on both sides.

Blue Wire - Connect to the (+) side of any led light(s) that you want to strobe continuously.

Note:  You do not have to use both the white wires and the blue wires at the same time.  You can and normally would use one or the other.

Installation:

The FM-00 module can be used in conventional (-) ground systems and (+) ground 12 volt systems.  It will not work in 6 volt systems.

Install the module anywhere between the battery power and the led light that you wish to make flash.  Connect the wires as follows:

Connect the flashing module in the wires feeding to any led bulb as follows:

Important:  The dual circuit module has the words "FLASHING CONTROL MODULE" molded into the black case.  The end closest to the word "FLASHING" must be toward the battery, and the word "MODULE" must be oriented closest to the led bulb.  If the module is installed backwards, it will not work.

Power must flow thru the module and then to the led lights or bulbs that you want to make flash.

Red Wires - Connects to the (+) brake light wire.

Black Wires - Connects to the (-) ground wire.